How to charge your phone if the socket is broken. How to fix the charging connector at home with video. ʘ Making a plug for charging from Nokia Replace the plug on the charger

It's no secret what a miniature plug the charger for NOKIA phones has. But due to its small size you need to be very careful with it.

Personally, I have already broken 2 of these.)) The first one did not survive the fall from my holey hands when the phone was charging. After that, I bought a cheap Chinese charger ($5), but it quickly broke down, and the metal pin quickly broke off due to poor quality... So what should I do? Should I buy a new one? — never!

“We need to find a connector and solder it instead of the old one” is the first reasonable thought. But the fact is that such a plug cannot be found separately! You can, of course, buy an expensive universal charger with connectors for all occasions, but will we need them later?

What we need:

— 20 ml syringe (smaller is unlikely to work)

— Any collapsible plug (optional)

— File with a sharp edge

— Needle for ball

It only takes 5 minutes, but it will be nice every time you charge your phone.

Step 1. Cut off the excess length of the ball needle. ( Cunning: To prevent the edges from flattening, you need to apply a stress raiser (small scratch) around the needle. After this, it will break off easily and smoothly. I don’t recommend sawing with a hacksaw, because... the needle will bend anyway.)

Leave 4-5 mm and about we process the end of the future plug.

Step2. We also break off the future core from the syringe needle. For ease of soldering and short circuit protection, I made it 25 mm long.

Now we isolate it with tape or a thin plastic tube and insert it into the needle from the pump.

Step3. We twist it. The positive red wire should go in the center. Be careful with soldering! Can damage insulation if overheated.

For a more aesthetic look, I put on a plastic piece from another power plug. Ready!

Conclusion: For mere pennies, we made a good plug for Nokia phones, which is many times stronger than the original one. This one will definitely survive any treatment))

It's hard to believe now that mobile devices were the easiest way to connect with other people. Now an ordinary mobile phone has turned into a high-speed smartphone with enormous multimedia functionality, and the case has begun to store the power of a good computer inside it. Using devices is very addictive and some people don’t even take a break for at least a short time. This kind of use takes a toll on charging, and constant recharging can damage one of the phone's most important connectors. You will learn how to fix the phone charging socket if it is broken in today's article.

Is it possible to repair the charging module socket?

How to fix the charging port on your phone at home? You need to figure this out thoroughly, then everything will work out. Careless use of a mobile device very often ends in some kind of breakdown that needs to be fixed. Sometimes the breakdown lies in the connector for connecting the power cable. In this case, you need to find out how to fix it, and for this you should familiarize yourself with the main causes of the defect.

The main reasons for device socket failure:

You can spill some liquid on the device or simply drop it thoroughly to disable this module.
Constant mechanical stress deforms the socket, which can make charging the gadget simply impossible - the plug will not fit into the connector or will dangle in it, in which case the socket will need to be replaced.
The contact pads may also bend, which will completely block access to electricity.

Let's talk right away about the worst thing - moisture.

Contact of a mobile phone connector with moisture is the most dangerous damage. Corrosion will start a chain reaction and all neighboring components will oxidize. This kind of defect can also damage the speaker, which is most often located in the lower part of the device. Also, the speaker itself allows moisture to enter the cable or connector. Therefore, even light rain can damage your phone.

Important! Find out what can be done, whether it is possible to revive the gadget if a more serious problem befalls you -.

The most important thing is to assess the complexity of the damage, since not all cases allow for home repairs. The best option is to use the services of a qualified specialist from a service center. This way you won’t risk breaking your device.

Is it possible to repair the device at home?

Very rarely restoration work can be carried out independently. It is best to find an alternative charging method for a while until you decide for yourself whether to repair it yourself. While you are saving the necessary amount for repairs in the workshop, read the instructions for charging a phone with a broken socket:

Insert the charger into your smartphone and plug it into the network.

Important! This method is only relevant for devices that have suffered from mechanical stress, and not from moisture.

Carefully move the cord and device in different directions. You may be able to close the contact and charge the device.
If the mobile phone nevertheless detects the presence of a charger, then it is worth recording the found position. Books and other items can be used that can install the phone so that the power continues.
Before carrying out all these actions, you should make sure that the problem is in the socket and not in the battery. Using your phone for a long time causes it to no longer hold a charge. In this case, you will have to get a new battery rather than deal with a “phantom” breakdown.
If the problem is still in the nest, then repairs cannot be avoided. If the socket is moving away from the tablet or the USB input is loose, try changing the socket itself or replacing the cable.

Important! Remember that all these manipulations can further loosen the socket, so do not use too much force during the work.

Alternative charging method

If the design of your phone allows you to remove the battery, then you can use a universal charger. Such devices are called “Frog”. It is, of course, not very cheap, but sometimes you urgently need to charge your phone. This gadget has special grooves into which you need to insert and secure the battery.

But this method also has a number of obvious disadvantages:

While charging, the smartphone will not work and cannot be used until the battery is charged.
The purchase price of “Frog” is quite high and does not always justify its purchase.
If the manufacturer's reputation is very dubious, then you will only harm your device.

We charge the device directly

How to fix the phone charging connector? You can try to replenish your energy reserves by disconnecting the power port itself from the phone.

Important! This method is very complex and requires the user to have basic knowledge and skills in working with equipment and electricity.

The essence of the work is as follows:

We remove the battery from the smartphone.
We unplug the charger from the outlet, arm ourselves with a sharp object and remove the insulation from the wire about five centimeters.
Strip the wires and determine where the plus is and where the minus is.
Determine the polarities on the battery and connect the wires to it.
Fix the improvised terminals and supply power from the network.

Important! It is not recommended to resort to this method, since you may get hurt even while charging. Do not work with wires without insulation if you have never done this before and do not know how electric current behaves.

Do-it-yourself repairs

You need to act very carefully if you decide to fix the phone charging socket with your own hands.

To disassemble the case and remove the socket we will need:

A small set of screwdrivers.
Technical tweezers (ordinary tweezers will do).
A stationery knife or a regular sharp one.
Soldering Station.

Now you need to do the following:

Unscrew all the screws that secure the housing.
Carefully remove the cover by prying it off with a utility knife.
We ground the soldering iron, solder the wire to the negative (device body). The second end of this wire must be connected to the body of the soldering iron itself.

Important! These measures are necessary to ensure that the mobile phone does not suffer from the accumulation of static electricity, which can damage parts. It would also be a good idea to make an antistatic wrist strap and ground it.

Now we unsolder all the wires from the socket. This is necessary to prevent short circuits.
Next, you need to remove the screws from the board that hold it in place. Now we have access to the microUSB connector.
We take out the old socket, solder a new one in its place, assemble the device in reverse order and check its functionality.

You may also find our instructions useful,

Problems with charging your phone are one of the most common reasons for contacting us for repairs. This is not surprising, because mobile devices are charged almost every day, but not always everything goes “smoothly”. It happens that the cord was pulled and the charging socket was damaged, or they used a “Chinese” charger or charged the phone from the cigarette lighter in the car. The reasons for charging problems may vary.

What can you do yourself?

Check the serviceability of the cord and charging unit. The advice is banal, but often they are the problem. The cord “frays” and there is no contact, and the charger unit may fail due to voltage surges in the network. Don't rush to buy new ones - try to borrow from friends/neighbors and make sure that the phone starts charging. And if it comes to buying a lanyard or charger, take only original ones, or check on the spot. If the accessories are of poor quality, the phone may also not take a charge.
Clean the charging connector from dust. Often, dirt accumulates in the Lightning socket (iPhone and iPad) or micro USB (Android phones), due to which there is no contact with the cord and the phone does not charge. To clean the socket from dust, it is advisable to turn off the phone and remove the battery (if this is provided by the design of the device). Then carefully! without any effort! Use a toothpick to pick out debris from the connector.

If these manipulations did not help, then...

Can't do without repairs

1. Replacing the charging socket

Symptoms:

the phone does not react in any way to connecting the charger;
the cord “comes off” - if you hold it at an angle, charging continues;
the micro USB socket is wobbly and most likely torn from the motherboard;
oxides are visible in the nest after moisture (for example, after rain);
contact group is damaged.

Repair options: sometimes restoration helps, but it is better to replace the socket. Different phone models are designed with different types of connectors. The most popular - micro USB - are usually soldered to the board. There are options when the sockets are installed on a cable and it is more cost-effective not to solder, but to change the cable assembly. For example, this is exactly the situation on all iPhones.

2. Restoring the electronics of the charging circuit

This is a more severe case. It usually occurs if you used non-original accessories or low-quality car chargers after water got inside the phone.

Symptoms:

when you connect the phone to a charger, the battery icon shows that the charge is in progress, but if you turn off the charger, the battery percentage remains the same or becomes even lower;
The phone does not turn on and does not respond at all to the power button. This is explained by the fact that in many models the charging controller and power controller are one chip.
The phone gets very hot and the battery drains quickly; the phone does not hold a charge.

Repair options: depends on the fault. Preliminary diagnosis is necessary. Perhaps everything can be done by washing it in alcohol (), perhaps you will have to resolder the charge controller chip.

3. Battery replacement

Problems with the battery can arise after improper use of the device (in severe frost or, conversely, overheating), as well as after the expiration of the life of the chemical element (the average period of operation of lithium-ion batteries is 2 years).

Symptoms:

the phone turns itself off at 15-30% charge, especially if you turn on 3G or the camera with flash;
the battery is swollen and the cover is sticking out (if there is a built-in battery);
The phone dials quickly, but does not hold a charge.

Repair options: replacing the battery. It is advisable to do a preliminary diagnosis to make sure that the cause is definitely in the battery.

How to fix a phone charging socket? How to fix a phone charging socket at home? Do not know? Let's figure it out and fix it at the same time. Are you ready? Then let's begin. If you use it carelessly, sometimes the power socket breaks. In this case, you should know how to repair the phone's charging connector or charge it in another way.

The main reasons for the breakdown of the charging socket

You can force the connector to break down if you have a habit of frequently dropping the device or spilling various drinks and other liquids on it. With constant impacts, the socket may become deformed, which will make charging the tablet impossible, since the plug simply will not fit into the connector, or may be blocked by some housing part that has shifted after a strong impact. The pin connectors may also bend when connected, then your gadget will not receive energy.

Damage from contact with a damp environment of the dock connector is much more dangerous. This can damage various neighboring components, which include the polyphonic speaker, which is always located at the bottom of the device. In most cases, it is the speaker, or rather its mesh, that is the conductor of liquid and moisture to penetrate into the device body to the cable and connector.

How to fix a phone charging socket at home

You must immediately indicate that your device cannot be repaired in this way. A broken power socket will remain so and repair cannot be avoided. This half-measure is necessary in situations where there is no required amount for repairs, but you need to use a mobile phone. Instructions on how to charge your phone if the socket is broken:

Connect the charger to the device, plug it into the network.
Try moving the cord, moving the plug position up and down.
If the battery cannot be charged because the contact has become loose, such actions can short-circuit it.
If your cell phone detects the charger, try to fix this position. Try placing books or other objects under the wire so that the mobile phone can lie there overnight and the battery can be charged. Before carrying out such a manipulation, make sure that the problem is really in the connector and not the battery. When used for a long time, they tend to stop holding a charge. In this case, you should buy a new battery rather than deal with a supposedly damaged socket. If the problem really is with the connector, then it is unlikely to be able to avoid repairs. Keep in mind that such manipulations with the wire can further loosen the connection point or completely break it.

Before carrying out such a manipulation, make sure that the problem is really in the connector and not the battery. When used for a long time, they tend to stop holding a charge. In this case, you should buy a new battery rather than deal with a supposedly damaged socket. . If the problem really is with the connector, then it is unlikely to be able to avoid repairs. Keep in mind that such manipulations with the wire can further loosen the connection point or completely break it.

Replacing the charging connector with a universal device

In a critical situation, when you don’t know how to charge your phone if the socket is broken, you can use a universal charger. Sometimes the device is called a “frog”, it is relatively expensive, so it is not a fact that it is better than sending the device for repair. This device has a special groove into which you need to insert the battery removed from the mobile phone. However, this method has several obvious disadvantages:

During charging, the smartphone is turned off and cannot be used until the battery is charged;
the cost of the “frog” is high and sometimes does not justify the costs;
among user reviews there are situations
when the charger broke the battery

If your phone's charging socket is completely broken, charge it directly

If you don't know how to change the charging socket on your phone, you can try to recharge the battery without having to use the power socket. The method is relatively complex and requires some skills in working with electricity. The point is this:

You need to remove the battery from your phone.
Cut off the insulation from the charger wire, expose the wires (unplug from the outlet).
Strip the veins, determine where the plus and minus are.
Find the corresponding terminals on the cell phone battery.
It is important to observe the polarity of the wires and the device. Secure the wires and plug the plug into the socket.

It is strongly not recommended to use this method if you are not 100% confident in your skills. You should not carry out manipulations when you are alone at home; there must be a person nearby who can help you in case of a possible electric shock. Please note that this connection option is not normal for the battery and can lead to breakdown or premature depletion.

The only proven way to get rid of the problem is to leave the matter in the hands of professional workers. You may not want to try any “workarounds” after they tell you how much it costs to fix your phone charging socket. In modern devices, this connector also performs the function of connecting to a computer and transferring data, so its failure greatly reduces the functionality of the device. This is a microcircuit that cannot be repaired at home on your own. Phone repairs often cost a lot of money and you should be prepared for this.

In this case, it is best to contact a certified center. The ideal option would be a branded service point from the same manufacturer as your mobile phone. They know all the intricacies of their products and will be able to provide qualified assistance to fix the breakdown. Inexperienced or careless workers can aggravate the situation and lead to even greater damage to the device.

Repairing a USB connector on a tablet - a failed connector on the board of a laptop, tablet or phone always causes a lot of trouble for the user. Breakdowns of the Universal Serial Bus port most often occur due to negligence. A standard example: the tablet is charging and someone accidentally touches the wire with their foot, it’s good if in this case the wire from the adapter is damaged, which is easier to replace, but if the USB port on the board of your device breaks out, then this will be more difficult. And there is no way to do it without disassembling the device. How to independently repair a tablet or phone and replace a faulty terminal with a new one will be discussed below.

There is nothing complicated about this type of repair such as re-soldering a connector, but naturally you need to have at least basic knowledge and skills in handling a soldering iron when working with printed circuit boards. Before you start work, you need to prepare the necessary tools, namely: a soldering iron with a power of 25 W, low-melting solder, preferably POS-61, medical tweezers, a set of screwdrivers, a cutting tool such as a scalpel or a paper knife, as well as a good magnifying glass.

Method of disassembling devices such as tablet, phone, laptop

One of the main principles is to do everything with great care and precision.

1. Unscrew all installed screws on your device, be it a laptop or a phone. To remove the back cover, you need to carefully insert the scalpel blade into the gap between the body and the cover, as if prying it up while simultaneously tilting the scalpel in the direction of the screen. This action will release the fastening clips and the cover will be easily removed.

2. After removing the cover from the tablet (hereinafter referred to as the device), be sure to ground the soldering iron. To do this, you need to take a piece of wire and solder one end to the common bus on the device board, and fasten the other end to the metal part of the soldering iron itself, perhaps near the handle, where the temperature is lower. Also, before starting work, do not forget to remove static voltage from your hands by placing them on the heating radiator in your apartment. This is done in order not to damage the electronic elements on the board, which are very sensitive to static. It’s even better and more reliable to work with an anti-static bracelet or simply fasten a piece of wire to your wrist and the other end to the radiator.

3. The next step is to disconnect the wire from the battery to avoid accidentally shorting any component on the circuit board.

Here is a small list of possible usb connector malfunctions that may occur under various circumstances and some options for repairing them.

The Universal Serial Bus port has failed

There are cases when, if the port is seriously damaged, the connector can no longer be restored; in this case, it is replaced with a new one or borrowed from another unnecessary device; you need to unsolder a known good connector from the donor and solder it in place of the broken one. To remove this part from the board, we again use a scalpel, which needs to be inserted between the PCB and the connector and, heating its leads with a soldering iron, carefully lift first one end, then the other. By the way, in order not to injure the contact pads of the board, it would be better to take a shielding braid from some wire, apply liquid flux to it and use it to remove the solder from the connector pins. If anyone doesn’t know how to do this, it’s very simple. You apply the braid to the contact pad and heat it with a soldering iron, the molten solder is absorbed into the braid and the pad remains free. This method will not damage the board and will not overheat the soldered part. Take special care when working with a soldering iron during installation, since there are SMD parts nearby that are installed on top of the board, without being installed in holes, so they can become unsoldered due to the high temperature emanating from the soldering iron.

The usb connector is working, but is torn from the board

If this happens, be sure to check the paths to see if there is a break somewhere. To do this, you can use a magnifying glass or you can ring the tracks with a multimeter. If everything is in order and the conductive paths are in good condition, then you are in luck. Otherwise, they will need to be restored. To do this, in the damaged area, the ends of the track should be cleaned with a scalpel and tinned. Now you need to install the USB connector on the board; for reliability, it is advisable to apply a little glue to its base, that is, place it on the glue, and then solder the pins. Now, in case of emergency situations with the connector, he will feel more confident, since glue and soldering double the reliability of the installation. We solder small pieces of tinned single-core wire onto damaged, broken tracks, thereby eliminating the break. There are times when for some reason it is not possible to restore the damaged area, then it will be possible to repair two tracks, that is, two terminals located at the edges, and use this connector only to charge the device.

Pinout of 5-pin connector

The Micro USB connector has five pins:

1 contact: +5 V power supply charging

2 contact: receiving signal (D-)

3 contact: transmit signal (D+)

4 contact: free. When connecting the OTG cable, it makes a short circuit to the case, this action searches for and installs a new device.

5 contact: common bus (minus)

Pinout of 4-pin USB connector

It often happens that the phone stops charging, although when you check the charging from it, it turns out that it is working. Thoughts arise: the phone is faulty. But not many people think that the reason for the lack of communication between the phone and the charger may be a simple clogging of the phone input socket. A fairly large number of phones do not have a protective cap on the USB input socket. Because many people carry their phones in their pockets, and over time they accumulate garbage, which quietly but surely penetrates the phone's socket.

If the phone has been in your pocket for a long time and has never been registered, then most likely its USB input socket is already clogged. If you're lucky, the phone charges normally and connects to the computer. It may be that there is a periodic loss of normal contact with charging. Well, in a bad case, the phone does not charge at all and does not connect to the computer, although everything is fine with the charging and the cable.

As soon as you start having problems with normal charging of your phone (the phone won’t charge, the charging is working), I immediately advise you to clean the USB input in your phone yourself. This is done quite simply. First, using a thin needle, we carefully try to scrape out debris from the depth of the phone input connector. This debris may be compressed pieces of dust and lint. It is this that usually prevents normal electrical contact between the charging plug and the phone input socket. It is difficult to remove this debris with a simple brush, but with a needle it is just right.

Next, after we have pulled out the compressed debris, we take a small brush in our hand and continue to clean the phone’s USB input socket from smaller particles of debris. Don’t forget to blow out this very garbage with your lips))). After completing such a simple phone cleaning, there is a high probability that your device will start charging normally again. Personally, I have several such successful cases when it helped. Although at first there were thoughts that I would have to take the phone for repair.

If this does not help, the next most common reason for the phone not charging normally is problems with the electrical contact of the socket itself and the board on which it is soldered. It is also not uncommon for a wire to break near the plug coming from the charger (inside). You can solder the wire yourself. Take it and cut the end of the plug near the wire coming from it. The break usually occurs at a distance of about 5 cm. We disconnect this piece of wire and re-solder the wire to the plug. Well, if the problem is in the socket, which has lost contact with the board, then only a repair service will help.

When your phone no longer holds a charge, the problem is likely with the power connector. This is one of the common reasons. First, it is important to make sure that the breakdown is actually only in it. Expert advice will help you figure out how to replace the charging connector.

How to identify a charging fault?

There are several ways to check whether the charging connector of iPhone, Samsung and other models needs to be replaced. First, you need to reproduce the events that preceded the fact that the device stopped charging. If the smartphone was dropped or the power cord was abruptly pulled out, dust or dirt got into the power plug, then all this could lead to damage to the power connector.

It is necessary to visually inspect with a phone. Its reaction after connecting the device to the network may indicate the need to replace the charging connector. If there is no reaction to this action, then we can talk about a malfunction of the connector.

Main reasons for failure

Replacing the charging connector of iPhone 5S, Nokia, Samsung and other types of phones may be required in several cases. The most common faults include:

Mechanical damage:

The plug is inserted incorrectly and the contacts are damaged.
The power cable is abruptly pulled out of the phone.
A foreign object has been inserted.
Falling or hitting a hard surface.

Pollution. Dust may get inside the devices. It could also be foreign parts that prevent the charger from working properly.

Moisture or liquid has entered. A flooded connector is often faulty. This causes the device to break the phone.

Defect in production. The connector paths were not soldered. After some time, a malfunction appears.

Often you have to deal with something that is already broken. Using such a device or experimenting with it is incredibly dangerous - you can break the equipment. It is important to remember that replacing the power connector on a phone includes a specific list of steps, depending on the type of phone. For example, in devices manufactured today, everything is incredibly small. The arrangement of the parts is tight. This makes repairs somewhat difficult.

How to change the connector on your phone?

When the device does not hold a charge, the fault is often detected in the power connector. This type of technology has very small parts. They fit tightly to each other. Therefore, it is important to exercise caution during the repair process. The master must have at least minimal experience in this matter. Otherwise, you may not only not fix the phone, but also break it completely. Replacing the charging connector of Samsung, Asus, iPhone and other brands is carried out according to a special scheme.

At the very beginning, you need to disassemble the smartphone so that you can remove the motherboard soldered to the USB connector. Among technologists and professional repairmen, this charging socket is called micro-USB. It is one of the most common power connectors.

There are also non-standard types of devices. For example, these are phones released in China. Many Asian manufacturers have recognized the need to standardize equipment. They try to release only phones with the presented connector. However, there are difficulties when repairing these types of smartphones. Although the socket may be the same for all phones, the attachment to the motherboard is sometimes different.

If the phone is completely disassembled, the technician inspects the damage and determines the actions required during the repair process.

Simple breakdown

Replacing the charging connector of an iPhone 5 or other popular brands of smartphones has a number of nuances. The power connector may not be damaged, but its pins have moved away from the system board.

This often happens when mechanical force is applied to the device. Perhaps the cord was pulled sharply when it was disconnected from the phone. In this case, you do not need to change the entire connector. Repairs will cost much less. You can solder the contacts yourself if you have the appropriate equipment and some experience in such work.

Complex breakdowns

Replacing the charging connector for Samsung, Lenovo and other brands of phones can be done using more complex technology. This will be required if the charging socket is noticeably damaged. In this case, it needs to be changed.

It is even more difficult if damage is visible in the socket, but it can only be replaced in conjunction with other parts. Today's devices are becoming even thinner, miniature, and the electronic components in them are becoming smaller. For example, the bottom board to which the power connector is soldered is very thin in certain models. It cannot withstand heat and becomes deformed. Then there is only one solution - to replace the connector only complete with this board. This increases the cost of repairs. There are frequent cases with new phone models where the power connector is built into the cable. Therefore, there is a need to change it complete with the cable.

Certain phone manufacturers have created a new design in which the screen must first be unsoldered before disassembly. Therefore, you cannot do without asking for help from a service center specialist. In order to replace the charging connector, you will need to heat and carefully remove the display module of the device. In this case, there is a high probability of damaging the screen. The cost of replacing the power socket increases.

If the work presented is performed by a non-professional, he may simply break the complex equipment. It’s better not to take risks, but to contact a trusted specialist.

How to charge your phone when you urgently need it

When you need to make an urgent call and the phone connector is broken, don’t despair. Before replacing the charging connector, you can charge the phone using available means.

The plates need to be buried in the ground, having previously wrapped them with copper wire. Salt water pours onto all this. This is the charger. When iron is not at hand, it can be obtained from scrap materials. For example, metal pins are inserted into lemons or apples. Wire is wound around them.

After familiarizing yourself with the features of replacing the charging connector, you can make the right decision on how to fix the problem.

Almost every person has a telephone. The device allows you to maintain contact with family and friends. Since the mobile phone is often used, some of its parts fail. One of the common problems is a broken charging socket. It costs to repair it in Russia from 1000 to 4000 rubles, sometimes more.

What is this?

Repairing a phone charging socket means replacing or restoring the functionality of a faulty connector.

The following signs indicate that repairs are needed:

The plug does not fit into the charging connector well.
When connecting the smartphone to the charger, power does not start.
When connected, the computer does not see the smartphone.
The plug keeps falling out of the socket.

There are many reasons for nest failures. Most often, these are oxidation processes on the contact tracks of the element, the phone falling, or natural failure of the part. The smartphone can be replaced or restored at the store where the device was purchased, or at a specialized service center.

If you need to repair a mobile phone charging socket, you should follow this algorithm:

Visit a service company and show the phone to a specialist.
Wait for the diagnosis to complete.
Find out the cause and type of failure.
Negotiate the cost of the work.
Agree to the repair.
Wait for the wizard to complete its work.
Check the functionality of the connector.
Pay the specialist for the service provided.

The time it takes to restore the charger connector is 30-45 minutes. An urgent replacement takes about 20 minutes.

What does the price depend on?

Service centers set different prices for restoring/replacing a mobile charging socket. The price is formed under the influence of the following factors:

Device model, brand.
Possibility of restoring the functionality of an old part.
Purchase price of new spare parts.
Type of parts purchased (original, non-original).
Urgency of order fulfillment.
Specialist qualification level.
Cost of diagnostics.
The price of calling a technician to your home.
Kudos to the service center.
Availability of a valid warranty for the device.

Types of repairs

The following types of repairs are distinguished:

By urgency – regular and urgent.
By type of work - restoration, replacement of parts.
According to the person who performs it, he is a professional master of a service company, independent.

Urgent professional repairs are the most expensive. It is cheaper to repair a mobile phone yourself or contact a private repairman.

Approximate prices

In Russian service companies, repairing a mobile socket connector costs approximately the following amount of money:

Diagnostics are free if you agree to restoration.
Recovery - 1800 rubles.
Replacement - from 1000 rubles(without the price of a new connector).

Examples of repair costs depending on the mobile model:

NTS – from 1000 to 2500 rubles.
Samsung Galaxy – 1100-4000 .
Samsung S – 1000-1100 rubles.
Nokia Lumia 1200-1500 .
Nokia N9 from 1300.
Nokia 6700 – 1100 .
Nokia E66 – 1300 .
Sony Xperia 1200-2000 rubles.
Apple iPhone 4/4s – 1300 .
Apple iPhone 6 – from 2000.
Apple iPhone 6s – 2500 .
Apple iPhone 6s+ - from 2500 rubles.
Apple iPhone 7, 8 — from 3000 rubles.
Apple iPhone X - from 4000 rubles.

How, where and from whom can I order this service?

If the connector for charging your phone is broken, you can repair it in three ways:

Take it to a service center.
Contact a private master.
On one's own.

If the phone is under warranty, then it must be taken to the store where it was purchased, or the service that should service it during the warranty period. Otherwise, you can contact a private technician or service center. The last option is preferable. Then a person receives high-quality diagnostics, repairs and a guarantee for the work done. Private owners often turn out to be illiterate, and then they have to take the phone to the service center.

Self-repair is possible. But to do this, you need to understand the device, have experience in repairing phones of a certain brand, and a set of necessary tools. Do-it-yourself restoration is cheap, but takes personal time and effort. In addition, there is a risk that the work will be performed incorrectly and the condition of the mobile will worsen.